PLEASE READINSTRUCTIONSSTORE UNDERCOVERFrontierFor Children 2 years and 25 lbs and up
8Harness Height AdjustmentNOTE: The harness height adjuster also adjusts the height for the head restraint in harness mode. The head restra
9Head Restraint AdjustmentWARNING: The head restraint adjuster is for booster mode only. DO NOT use the head restraint adjuster when the harness
10Adjusting Buckle PositionRemoving the BuckleUnbuckle the harness. 1 Locate the metal buckle strap 2 retainer on the bottom of the child se
11Re-threading the BuckleIMPORTANT: Select the slot closest to, but not under the child. Turn and push the buckle retainer 1 so that the short si
12Fastening the BuckleInsert one tongue at a time into the buckle. NOTE: Proper connection is confirmed with a positive click after inserting each buck
13Locate the LATCH anchors in your 2 vehicle.Verify that the LATCH connector 3 is right-side up and that the LATCH strap is not twisted before
14Remove the Versa-Tether from the 1 storage clip. Loosen the tether and place over 2 the child seat back.Tilt the tether adjuster tab and pull 3 to
15Using the Chest Clip Opening the chest clip. 1 IMPORTANT: The correct height for the chest clip is at the middle of the chest at armpit level.Using
16Using the Cup HoldersPull the handle up and out to open 1 the cup holder. Push the base of the cup holder 2 down to lock into place.Push the b
17Based on crash statistics, the National Highway Traffic Safety Administration recommends that parents select a rear seating position as the s
18Vehicle seat belts and LATCH anchor locations vary. Consult your vehicle owner’s manual for details on what type of seat belts your vehicle
19If your belt type is listed below, select another seating position or use the LATCH connectors.The following types of vehicle belts are not compatib
20Harness ModeNOTE: This seat is shipped with the recline block in booster mode.IMPORTANT:This child seat can be installed using LATCH, a lap-shoulder
21When positioning this child •seat in booster mode use the vehicle’s lap-shoulder belt to secure the child and child seat into the desired
22LATCH – Short Path OnlyChecklist for proper installation:Does your vehicle:Have a top tether anchor? 9Always use the Versa-Tether * for children
23Harness ModeLocate the LATCH anchors in your 5 vehicle.Verify that the LATCH strap is not 6 twisted.Attach the LATCH connectors to 7 their adjac
24Lap-Shoulder Belt – Selecting a Belt PathDue to the variability in vehicle seat designs and belt systems, the Frontier child seat can be secure
25If the buckle stalk is to the C side of the child seat (i.e. the child seat is narrower than the insertion points of the vehicle belt syste
26Harness ModeLap-Shoulder Belt – Short PathChecklist for proper installationDoes your vehicle:Have a seat belt that can be locked? 9Check your vehic
27Harness ModePull the vehicle belt out and route 5 the belt through the first belt slot, under the cover and through the second belt slot.Verify th
ContentsThis product and its components are subject to change without notice.© 2008 Britax Child Safety, Inc. All rights reserved. Printed in U.S.A. P
28Harness ModeLap-Shoulder Belt – Long PathChecklist for proper installation Does your vehicle:Have a seat belt that can be locked? 9Check y
29Harness ModePull the vehicle belt out. Route the lap 5 portion of the belt over the red lap belt guide, while positioning the shoulder portion o
30If the vehicle has a tether anchor 1 for the chosen seating position, then remove the Versa-Tether from the storage clip.Harness ModeLap Belt
31Harness ModePull the vehicle belt out and route 5 the belt through the first belt slot, under the cover and through the second belt slot.Verify th
32This seat can be used in booster mode with children who stand 42” – 60” (106.7 – 152.4 cm) in height and weigh more than 40 lbs (11.3 kg). Britax re
33On the bottom of the seat, turn the 5 metal retainer of one harness strap so it will slide through the slot.Pull the harness webbing tight * from t
34Booster to Harness ModeTo replace the harness and buckle:Locate the harness assembly.1 Ensure that harness slots in cover, 3 head restraint and
35Turn the metal retainer of one 6 harness strap so it will slide through the slot.Ensure that the harness strap * is not twisted. Push the
36LATCHChecklist for proper installation:Does your vehicle:Have a top tether anchor in the chosen seating position? 9Have LATCH anchors in the chosen
37Booster ModeUnhook the Versa-Tether1 ® hook from the storage clip.Ensure the recline block is in the 2 booster position.Place the child seat on
2Registration and Certification InformationChild seats could be recalled for safety reasons. You must register this child seat to be reached in a recal
38Lap-Shoulder BeltBooster ModeEnsure that the recline block is in 1 booster position.Place the child seat on the vehicle 2 seat.Use the vehicle’s lap
39Securing Your ChildWARNING: Harness ModeNever route the vehicle belt over the child when using this child seat •in harness mode. Adjust the belts
40Fasten the child seat buckle.6 Securing Your ChildHarness ModePlace the child in the child seat 5 and position the harness straps around t
41Securing Your ChildFasten the chest clip.7 The correct height for the * chest clip is at the middle of the chest at armpit level.The HUGS™ chest
42Booster ModeSecuring Your ChildBooster ModePlace the child seat on the vehicle 1 seat and have the child sit in the child seat.Adjust the h
43Securing Your ChildBooster ModeRoute the shoulder portion of the 4 vehicle belt through the upper belt guide.Fasten the vehicle belt across the 5 ch
44Cover Removal Care and MaintenanceWARNING: Do not take apart the harness. •Never remove the buckle tongues from the harness. They cannot be •reatt
45Remove the screw to unlock the 5 head restraint adjuster. Raise the head restraint to the highest position.Store the screw in a safe pl
46Cover Removal continued Pull the cover from the lower 10 belt guides. Pull the harness straps, buckle 13 tongues, HUGS™ chest pads, and
47Replacing the CoverCare and MaintenanceMove the head restraint to the 1 highest position.Remove the screw to unlock the * head restraint adj
3General WarningsThis child seat must not be used in the home, in boats, or other •non-certified applications. To prevent injury due to deteriora
48Route the harness straps behind 7 the belt shield and re-attach to the harness yoke.Ensure the harness straps are * not twisted.Replace screw in
49Push the fabric into the 13 groove around the cup holder housing.Care and MaintenancePush the fabric under the lower 14 belt guides.Re-attach t
50Cleaning the Harness SPONGE CLEAN the harness using warm water and mild soap.• TOWEL DRY• DO NOT:•Disassemble the harness* Bleach* Machine wash*
51Turn the retainer so that the short 3 side will pass through the slot in the child seat shell.Care and MaintenancePull the retainer through the s
52Turn and push the buckle retainer 2 so that the short side will pass through the slot in the cover and child seat shell.Care and MaintenancePu
53Energy-Absorbing TetherIMPORTANT: The energy-absorbing tether has been designed to help indicate when the child seat has been in a
54TroubleshootingProblem: The harness is hard to adjust.Possible Solution: Check that the head restraint adjust and harness adjust are properly ali
55WarrantyThis child seat was manufactured by Britax Child Safety, Inc. Britax® warrants this product to the original retail purchaser as follows:LIMI
56Notes
4This child seat is for use forward-facing only with children who meet all of the following fit requirements.Harness Mode:Children must:be at least two
Double Check Car Seat-to-Vehicle Installation:Check that the LATCH or vehicle seat belt connections to the vehicle are tight and secure.Verify th
5Child Size: Height and Weight LimitationsBooster Mode:Children must:stand 42 – 60 in. (106.7 – 152.4 cm) in height 1 andthe top of the child’s ears
6Head Restraint1 Head Restraint Cover2 Harness Slot3 Comfort Pads4 HUGS™ Chest pads5 Harness Straps6 Chest Clip7 Arm Rest8 Lap Belt Guide9 Buckle10 21
7LATCH Connector Storage Slot22 Harness Yoke23 Head Restraint Adjuster Lock24 Head Restraint Adjuster Release25 Manufactured Date and 26 Expiration Da
Comentários a estes Manuais